code

Lexicon: eco.wonderland.workcell.asset.data.defs
Type: string

bdx: Largest diameter of the body of a tool item.
lbx: Distance measured along the X axis from that point of the item closest to the workpiece, including the cutting item for a tool item but excluding a protruding locking mechanism for an adaptive item, to either the front of the flange on a flanged body or the beginning of the connection interface feature on the machine side for cylindrical or prismatic shanks.
apmx: Maximum engagement of the cutting edge or edges with the workpiece measured perpendicular to the feed motion.
dc: Maximum diameter of a circle on which the defined point Pk of each of the master inserts is located on a tool item. The normal of the machined peripheral surface points towards the axis of the cutting tool.
df: Dimension between two parallel tangents on the outside edge of a flange.
oal: Largest length dimension of the cutting tool including the master insert where applicable.
dmm: Dimension of the diameter of a cylindrical portion of a tool item or an adaptive item that can participate in a connection.
h: Dimension of the height of the shank.
ls: Dimension of the length of the shank.
lux: Maximum length of a cutting tool that can be used in a particular cutting operation including the non-cutting portions of the tool.
lpr: Dimension from the yz-plane to the furthest point of the tool item or adaptive item measured in the -X direction.
wt: Total weight of the cutting tool in grams. The force exerted by the mass of the cutting tool.
lf: Distance from the gauge plane or from the end of the shank to the furthest point on the tool, if a gauge plane does not exist, to the cutting reference point determined by the main function of the tool. The cuttingTool functional length will be the length of the entire tool, not a single cutting item. Each cuttingItem can have an independent functionalLength represented in its measurements.
crp: Theoretical sharp point of the cutting tool from which the major functional dimensions are taken.
l: Theoretical length of the cutting edge of a cutting item over sharp corners.
drva: Angle between the driving mechanism locator on a tool item and the main cutting edge.
wf: Distance between the cutting reference point and the rear backing surface of a turning tool or the axis of a boring bar.
ic: Diameter of a circle to which all edges of a equilateral and round regular insert are tangential.
sig: Angle between the major cutting edge and the same cutting edge rotated by 180 degrees about the tool axis.
kapr: Angle between the tool cutting edge plane and the tool feed plane measured in a plane parallel the xy-plane.
psir: Angle between the tool cutting edge plane and a plane perpendicular to the tool feed plane measured in a plane parallel the xy-plane.
n-per-a: Angle of the tool with respect to the workpiece for a given process. The value is application specific.
bs: Measure of the length of a wiper edge of a cutting item.
sd-lx: Length of a portion of a stepped tool that is related to a corresponding cutting diameter measured from the cutting reference point of that cutting diameter to the point on the next cutting edge at which the diameter starts to change.
st-ax: Angle between a major edge on a step of a stepped tool and the same cutting edge rotated 180 degrees about its tool axis.
d-cx: Diameter of a circle on which the defined point Pk located on this cutting tool. The normal of the machined peripheral surface points towards the axis of the cutting tool.
hf: Distance from the basal plane of the tool item to the cutting point.
re: Nominal radius of a rounded corner measured in the X Y-plane.
l-fx: Distance from the gauge plane or from the end of the shank of the cutting tool, if a gauge plane does not exist, to the cutting reference point determined by the main function of the tool. This measurement will be with reference to the cutting tool and MUST NOT exist without a cutting tool.
bch: Flat length of a chamfer.
chw: Width of the chamfer.
w1: Insert width when an inscribed circle diameter is not practical.

Referenced By

chamferFlatLength eco.wonderland.workcell.asset.cutting.item.measurement.defs
chamferWidth eco.wonderland.workcell.asset.cutting.item.measurement.defs
cornerRadius eco.wonderland.workcell.asset.cutting.item.measurement.defs
cuttingDiameter eco.wonderland.workcell.asset.cutting.item.measurement.defs
cuttingEdgeLength eco.wonderland.workcell.asset.cutting.item.measurement.defs
cuttingHeight eco.wonderland.workcell.asset.cutting.item.measurement.defs
cuttingReferencePoint eco.wonderland.workcell.asset.cutting.item.measurement.defs
driveAngle eco.wonderland.workcell.asset.cutting.item.measurement.defs
flangeDiameter eco.wonderland.workcell.asset.cutting.item.measurement.defs
functionalLength eco.wonderland.workcell.asset.cutting.item.measurement.defs
functionalWidth eco.wonderland.workcell.asset.cutting.item.measurement.defs
incribedCircleDiameter eco.wonderland.workcell.asset.cutting.item.measurement.defs
insertWidth eco.wonderland.workcell.asset.cutting.item.measurement.defs
pointAngle eco.wonderland.workcell.asset.cutting.item.measurement.defs
stepDiameterLength eco.wonderland.workcell.asset.cutting.item.measurement.defs
stepIncludedAngle eco.wonderland.workcell.asset.cutting.item.measurement.defs
toolCuttingEdgeAngle eco.wonderland.workcell.asset.cutting.item.measurement.defs
toolLeadAngle eco.wonderland.workcell.asset.cutting.item.measurement.defs
toolOrientation eco.wonderland.workcell.asset.cutting.item.measurement.defs
weight eco.wonderland.workcell.asset.cutting.item.measurement.defs
wiperEdgeLength eco.wonderland.workcell.asset.cutting.item.measurement.defs
toolingMeasurement eco.wonderland.workcell.asset.cutting.tool.lifecycle.defs
bodyDiameterMax eco.wonderland.workcell.asset.cutting.tool.measurement.defs
bodyLengthMax eco.wonderland.workcell.asset.cutting.tool.measurement.defs
cuttingDiameterMax eco.wonderland.workcell.asset.cutting.tool.measurement.defs
depthOfCutMax eco.wonderland.workcell.asset.cutting.tool.measurement.defs
flangeDiameterMax eco.wonderland.workcell.asset.cutting.tool.measurement.defs
functionalLength eco.wonderland.workcell.asset.cutting.tool.measurement.defs
overallToolLength eco.wonderland.workcell.asset.cutting.tool.measurement.defs
protrudingLength eco.wonderland.workcell.asset.cutting.tool.measurement.defs
shankDiameter eco.wonderland.workcell.asset.cutting.tool.measurement.defs
shankHeight eco.wonderland.workcell.asset.cutting.tool.measurement.defs
shankLength eco.wonderland.workcell.asset.cutting.tool.measurement.defs
usableLengthMax eco.wonderland.workcell.asset.cutting.tool.measurement.defs
weight eco.wonderland.workcell.asset.cutting.tool.measurement.defs

Schema

{
  "type": "string",
  "knownValues": [
    "bdx",
    "lbx",
    "apmx",
    "dc",
    "df",
    "oal",
    "dmm",
    "h",
    "ls",
    "lux",
    "lpr",
    "wt",
    "lf",
    "crp",
    "l",
    "drva",
    "wf",
    "ic",
    "sig",
    "kapr",
    "psir",
    "n-per-a",
    "bs",
    "sd-lx",
    "st-ax",
    "d-cx",
    "hf",
    "re",
    "l-fx",
    "bch",
    "chw",
    "w1"
  ]
}